Skip to main content
#
Quick Release Fasteners
my account
site map
contact
cart
Search
 

If you are looking for a specific part, type in the corresponding part number. Or try our Site Map. If you are unsure of the exact part number, type the first 3 letters or numbers and put an * after it to broaden your search results.


 

Z-Spec Fasteners

When using Z-Spec fasteners you will need at least 2 parts to make up the system. A stud, and "S" Spring Receptacle. Optional Grommets, Retainers, Weld Tabs and ancillaries may be required depending on how you want the assembly to perform.

When designing a new application it is best to select components from the inside out.

  • First, determine which series (diameter) and Spring Receptacle you want to use.
  • Next, select the Grommet or Retainer you wish to use (if required).
  • Then, select a Stud Length (dash number) for the Total Material Thickness (TMT)            
  • Finally, select a Stud Style and Material.

Once you have selected the components to be used, be sure to get the appropriate associated tooling. The required tools will be determined by the parts you select.


 


Reference Information: We have included some tables and drawings at the bottom of this page to assist in the parts selection process. If you have any questions or need additional information, please Contact Us and we will be glad to help. How to measure for Z-Spec (Dzus®) Fasteners and Other Helpful Hints. All dimensions are in inches unless otherwise specified. For metric conversion use this formula: Inches x 25.4 = mm.  mm ÷ 25.4 = Inches.

Figure 1

In figure 1 above, A is the outside panel. B is the wall thickness of the flare grommet or thickness of the retainer if one is used. It could also be a gasket (compressed) or gap if any exists between panels in the application. C is the inside panel or support structure to which the receptacle (spring) is mounted. Add all of these dimensions together to come up with your TMT (total material thickness) which will be used to calculate the proper stud length and spring height for the application.

Figure 2

Figure 2 above shows how to measure the grip length (L) of an existing stud. This grip length is denoted as the dash number portion of the full part number. For example, part number MSAJ5-50 measures .50" in grip length. Z-Spec fasteners typically vary in length by .050" increments from size to size (.50", .55", .60" etc.). For oval head studs measure from under the head to the bottom of the detent where the spring sits when locked. For flush head studs measure from the top of the head to the same point. W is the head diameter which will indentify the stud's series.

Figure 3

Figure 3 above shows the rivet spacing (D) and the height (H) of a typical Z-Spec spring receptacle. All springs in a given series have the same rivet spacing. For example series 5 springs all have 1" spacing from center to center of the attachment (rivet) holes. Within each series there are different heights which, when used with different stud grip lengths, allows the installer to calculate the proper panel fit. The spring part numbers denote the the series first and then the height as a dash number. For example part number MS6-375 is a #6 series with a height (H dimension) of .375". The table below shows the rivet spacing for each series.

 

Series Rivet Spacing (D)
S3-xxx .625" (5/8")
S4-xxx .750" (3/4")
S5-xxx 1.0" (1")
S6-xxx 1.375" (1-3/8")
Figure 4

Figure 4 above depicts the correlation of alignment between the stud's slot (or wing) and the 'S' spring receptacle attachment. As you can see, the stud's slot will always align with the rivet holes of the spring. Therefore, regardless fo the mounting angle of the spring, the stud slot will always align with it. This is helpful for planning how the installation will look and also gives a visual sign of an unlocked fastener.


This website offers general information and easy access to our products. If you need detailed technical expertise, please contact our design team with specific requests.

About Quick Release Fasteners

We appreciate the support from everyone that uses Genuine MilSpec Products, and over the years it has been that support which has led to our growth. We will continue to work hard to provide fast, friendly and dependable service that will earn your trust in the future.


All content Copyright 1993 - 2016© MilSpec Products, Inc., All Rights Reserved. Trademarks® referenced are the property of their respective owners and do not indicate affiliation with Quick Release Fasteners or MilSpec.

 

Contact us
MilSpec Products / Quick Release Fasteners
31537 Long Acres Dr.
Sorrento, FL 32776
352-735-0065
352-735-0065 (fax)
milspecprod@earthlink.net

MilSpec makes no claims regarding suitability of items for any application. Installer is responsible for proper installation and any regulatory compliance.